19.6 square metres, and no two of them face the same way
A 2.5 m ball carries 4πr² of surface, which is about 19.6 m² — roughly a small bedroom wall, except that every square centimetre of it points somewhere else. At P5 that comes to 1,571 pixels around the equator and 785 from pole to pole, so a little over 1.2 million pixels in total, on a shell that lands near 350 kg at 18 kg per square metre. Peak draw sits around 19.6 kW, which is why the distribution board gets sized from this figure and not from the label on one power supply.
That is also the short answer to the first question every buyer asks: why does a ball cost more than a flat wall of the same area? Because the cabinets are not boxes. Each one is a wedge curved on two axes, and the tooling for those wedges is charged once, on the first unit.
P5 is the sensible pitch at this size, not the sharpest
Put a 2.5 m sphere on a plaza and people stand 5 to 8 metres back, often more. At P5 the pixel is 5 mm, so at 5 m the dots start to merge and the image holds; at 10 m it reads as continuous motion. Dropping to P2.5 quadruples the pixel count to nearly 5 million, which means four times the receiving cards, four times the heat inside a sealed shell, and a price that climbs by half again for sharpness nobody walks close enough to see.
The exception is a hotel foyer where the ball sits at head height and guests walk around it. There P2.5 or P3 earns its money. Outside, on a base, with a 6 m viewing distance, P5 is the honest answer and we say so even when the bigger number would pay us more.
A sealed shell still has to breathe
IP65 outdoors is not a matter of gluing modules down harder. It is a gasket line that runs unbroken across every cabinet joint, cable glands that are actually torqued rather than hand-tight, and a pressure equalisation vent. Without that vent, the 8 cubic metres of air inside the ball heats to 45 °C in the afternoon and cools overnight, and the pressure difference pulls moisture in through the weakest point in the chain. The vent lets the pressure move without letting water through.
Rear access is the other half of it. Water arrives from the front, but faults get fixed from the back, so the service doors have to open without breaking the gasket line above them. On a ball that means the doors sit on the lower hemisphere wherever the mounting gives us room.
The base takes the wind; the shell only carries itself
Outdoor units stand on a welded steel ring with eight anchor points, and the shell bolts to a central hub instead of hanging its own weight off the modules. The wind figure is the one people underestimate: 2.5 m diameter gives 4.9 m² of projected area, and a 30 m/s gust on that is about 3 kN — call it 300 kg pushing sideways at the hub. The base is drawn for that load, and the anchor plan ships with the shell so the foundation can be cast before the unit arrives.
On a hung sphere the same 300 kg goes into the ceiling structure instead, which is a different conversation with a different engineer. Ask which one you are having before you approve the mounting detail.

The domes behind it are the same tooling with a lid removed
Those two black frames are domes, and they come off the same wedge tooling as the ball in front: cut a sphere at a latitude and the cut edge becomes the mounting flange. Same curvature, same cabinets, less surface, plus a ring of steel around the opening. What changes is the load path — a dome can hang from a ceiling void because its flange spreads the load in a circle, while a full ball on the ground needs the hub and the base.
If you are buying both, quote them together. The wedges and the mapping work are shared, so the second shape is usually cheaper than the first one was.
What runs before the crate closes
The ball in the photo is not lit for the camera. It runs a full white field for half an hour, because white is the honest test — dead pixels show as black dots, weak modules as grey patches, colour shift as pink or green zones. Then patterns, then a soak. A seam that is 2 mm out reads as a visible line on flat colour, and on a sphere you cannot re-shim it once it is in a crate.
Then it comes down and gets a module map with every cabinet numbered. That sheet travels inside the box. Two years later, when a module dies, the replacement is matched from the map rather than from a photograph of the ball at night.
Five things we need to price it properly
Diameter, mounting (base, hub or hung), viewing distance, environment, and content format. Environment is not a formality: a coastal site changes the sealing and the stainless grade, a desert site changes the thermal design, a covered plaza lets us drop the brightness and save power. Content format decides whether you get a useful quotation or an argument later — a 2:1 equirectangular file plays correctly, a 16:9 video will stretch at the poles and we will say so before you sign.
Send those five and the quote comes back itemised: shell, base, control, mapping template and spare modules on separate lines, so you can see exactly which part the money is sitting in.

