Same pitch, same diameter, forty percent apart
Two quotes land on the desk for a 3 m outdoor sphere at P2.5. One is 40% above the other. Both are from factories that do this work, both list the same pixel pitch, the same brightness, the same IP rating.
The line that explains the gap is almost never written on either document. It is how many different boards the build needs, and how many spares of each you are quietly agreeing to buy.
Count the repeats
A shaped screen is cheap where the shape repeats. On a sphere, one latitude band is one board type, identical all the way around, so a 3 m sphere at P2.5 usually lands at ten to fourteen types. A 1 m sphere needs six to eight, simply because there are fewer bands. A ring or torus runs eight to sixteen.
Free-form sculpture is the other end. A twelve-petal flower, a tree with seven leaves, a letterform with a curved return: nothing repeats, every piece is its own drawing, and the type count goes to forty, sixty, ninety. That is where a quotation stops being predictable.

What a type costs before a single LED is bought
Each type carries a mask or a mould, an SMT program with its own feeder setup, a first-article inspection, a test fixture, and a spare stock line that has to exist for the life of the screen. Fixed cost per type sits in the low hundreds of dollars, and it does not shrink if the project does.
Ten extra types is a few thousand dollars before production starts. On a small job that is the whole margin, which is why a factory quoting a sculpture cheaply is usually planning to cut boards out of standard panels and hope nobody looks closely.
You cannot just cut a rectangle
The LED grid has to stay on pitch across the whole surface. Cut through a pixel and you lose a channel. Cut between channels and the edge lands halfway through the driver IC count, so the last row of the board behaves differently from every other row, and the seam glows.
Outdoor boards add a second problem: the cut edge is bare laminate, and that is where water enters. A cut board works on the bench and fails in the second rainy season. Any supplier who offers to trim standard panels for a curved surface is telling you what the third year will look like.

The spare list is the second invoice
Spares are usually quoted as a percentage of modules, often 1%, with a minimum per type. The percentage sounds reasonable until you apply it to a sculpture with sixty types: 1% of a small area rounds up to two boards per type, so the minimum becomes 120 boards regardless of how big the screen is.
Ask for that list, priced, at quotation stage. It is the single line most likely to double between the order and the first repair.
Where the type count really explodes
Domes and caps, because the band length collapses toward the pole. Fine pitch, because a shorter board means more bands across the same arc. A 76 square metre P4 dome can need 40 to 60 types while a 170 square metre P3 bowl needs 25 to 35, and the smaller one is the harder build.
Letters and logos are the quiet one. A single 2 m letter with a serif has an outer curve, an inner curve and two terminals, and every one of them is a different board.
Five questions for the next RFQ
1) How many unique board types, and how many spare boards of each. 2) Are the boards within one band fully interchangeable, or is each one keyed to a position. 3) Is the pitch constant across the whole surface, or coarser at the pole. 4) Which boards are cut from standard panels and how the edge is sealed. 5) What the price is for one extra of the rarest type, three years from now.
A supplier who can answer all five in writing has done this before. One who answers three and changes the subject is quoting a flat screen with a curved drawing attached.
Where to spend the savings instead
If the type count has to come down, do it in places nobody stands. Coarsen the pitch at the pole of a sphere, or blank the top 300 mm. Build a hemisphere instead of a full sphere when the back is against a wall. Reuse band modules on the section facing a building instead of the public side.
Do not do it at eye level. The equator of a sphere and the rim of a bowl are where people put their faces, and that is the last place to save two hundred dollars per square metre.

